Kali detects the adapter and seems to enable monitor mode but when I run ifconfig I get the following: I have bridged my hosts network connection Intel R Wireless-N with Kali and I have set up the Alfa nha as a usb device for kali through virtualbox. I downloaded Ath9k-htc from Github here, https: The awusnha comes with an atheros ar chip. I was asking if you go the same issues even after a reboot and attempt to connect it to your VM. So after researching for some hours, and trying several ways to troubleshoot the issue, the answer for me was to set the USB 3. By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of service , privacy policy and cookie policy , and that your continued use of the website is subject to these policies.

Uploader: Kigacage
Date Added: 22 October 2008
File Size: 7.83 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 66717
Price: Free* [*Free Regsitration Required]

Now you can use airodump-ng, aireplay-ng commands:. I downloaded Ath9k-htc from Github here, https: If anyone followed the video the OP posted, got wlan0 showing up in ifconfig but are stuck with the virtual box USB indicator blinking red.

Alot of the times the adapter just cuts off when I start Kali and when I boot up Kali and then connect the adapter it dosent switch on as it should. Yes I have checked but it does not find it. But yes, I would love to have the proper driver, awus036bha if it is a pain in the butt.


If I connect to a wifi with in the host with kali and alfa running the alfa stops working in kali Would really appreciate it! Like watch a movie, updating the system and so on.

Using Alfa awus036nha kali linux

Ive also installed the VirtualBox 4. FF wlan0mon You can also try to use the command wash wash -i wlan0mon Common errors Solution alaf “wlan0 is not injecting or proximity is low” Two things could cause this situation: By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service.

Code 7 normally means that you attempted to transfer data in this case, your deauth before associating with the AP. I know it has a Atheros AR chipset.

networking – How to get Alfa awusnha to work with Kali Linux? – Super User

All in all, an easy to set up and use device that I’m looking forward to playing with for some wireless testing. Kali detects the adapter and seems to enable monitor mode but when I run ifconfig I get the following: Now you can use airodump-ng, aireplay-ng commands: I thought that maybe it didnt have the right drivers so i tried to apt-get install firmware-atheros but it said that it was already installed.

So basicly the question is. Introduction Alfa wifi adapters became famous because of its quality and the power of the device. Sign up using Facebook. Found 2 processes that could cause trouble. It should not be a network setting issue, since you are attempting to manually pass a USB device to the VM.


This adapter is only for 2. Alfa has a lot of counterfeit models, make sure you buy the original. Jaime Polo 11 1. After I had the device filter setup, I detached the device from my workstation and logged into Kali.

Now however the problem is that when I plug in the Alfa device my network connection from my other wifi ceases to work Intel R Wireless-N the connection bridged aus036nha my host. Post as a guest Name.

Do you get the same failure message on USB 2. Great work, the pass-through worked flawlessly and I was up and running very quickly. Hi, I followed the steps you mentioned but not able to get the Alpha adapter detected and work in Kali Linux.


Sorry for the delay. My goals with these posts is that other people can easily learn from them, and that I can use them as a reference in the future. That is definitely one of my favorite things about a lot of the Alfa cards.

Sign up using Facebook.

Author: admin